Position and Size

Specifies the size and the position of the selected image, frame, or OLE object on a page.

Размер

Ширина

Задайте желаемую ширину для выбранного объекта.

Относительно

Рассчитывает ширину выбранного объекта в процентах от ширины области печати страницы.

Relative width relation

Определяет значение для ширины 100%: либо текстовая область (без полей), либо вся страница (включая поля).

Высота

Задайте желаемую высоту для выбранного объекта.

Относительно

Рассчитывает высоту выбранного объекта в процентах от высоты области печати страницы.

Relative height relation

Определяет значение для высоты 100%: либо текстовая область (без полей), либо вся страница (включая поля).

Пропорционально

Сохраняет соотношение высоты и ширины при изменении ширины или высоты.

Исходный размер:

Восстанавливает исходные значения параметров размера выбранного объекта.

Автоматически

Автоматически подстраивает ширину или высоту врезки к её содержимому. При необходимости можно указать минимальную ширину или высоту врезки.

Привязка

Specify the anchoring options for the selected object or frame. The anchor options are not available when you open the dialog from the Styles window.

К странице

Привязывает выбранное к текущей странице.

К абзацу

Привязывает выбранное к текущему абзацу.

К символу

Привязывает выбранное к символу.

Как символ

Привязывает выбранное как символ. Высота текущей строки изменяется в соответствии с высотой выбранного.

Положение

Задайте положение выбранного объекта на текущей странице.

По горизонтали

Select the horizontal alignment option for the object. This option is not available if you chose "anchor as character".

от

Enter the amount of space to leave between the left edge of the selected object and the reference point that you select in the To box. This option is only available if you select "From Left" in the Horizontal box.

к

Select the reference point for the selected horizontal alignment option. The following options are available:

• Paragraph area: the object is positioned considering the whole width available for the paragraph, including indent spaces.

• Paragraph text area: the object is positioned considering the whole width available for text in the paragraph, excluding indent spaces.

• Left of paragraph text area: the object is positioned in the region from the left text boundary to the first character on the left edge of the anchored paragraph text. For multicolumn paragraphs, the region is defined in relation to the column where the anchor is located. When the anchor is not located in the first column, then the region starts at the left column margin.

• Right of paragraph text area: the object is positioned in the region from the last character on the right edge of anchored paragraph text to the right text boundary. For multicolumn paragraphs, the region is defined in relation to the column where the anchor is located. When the anchor is not located in the last column then the region ends at the right column margin.

• Left of page text area: the object is positioned in the region between the left edge of the page and the left margin plus any left page padding.

• Right of page text area: the object is positioned in the region between the right edge of the page and the right margin plus any right page padding.

• Entire page: the object is positioned considering the whole width of the page, from the left to the right page borders.

• Page text area: the object is positioned considering the whole width available for text in the page, from the left to the right page margins.

• Character: the object is positioned considering the horizontal space used by the character.

Be aware that the set of options available depend on the Anchor settings. Therefore, not all options listed above may be shown due to the current Anchor choice.

Зеркально на чётных страницах

Меняет текущие настройки выравнивания по горизонтали на чётных страницах.

По вертикали

Select the vertical alignment option for the object. The selection specifies the position of the object relative to the region or reference line selected in the to dropdown list.

от

Enter the amount of space to leave from the top edge of the object to the region or reference line selected in the to dropdown list. This option is active only when the following combinations of Vertical and Anchor are selected. For these combinations, you can specify the amount of space to leave from:

Vertical		with Anchor
Сверху	Top edge of selected region. Positive values move the object down, negative values up.	To page, To paragraph, To character or To frame
Снизу	Selected reference line. Positive values move the object up, negative values down.	To character or As character

к

Select the region or reference line for the vertical alignment. The object can be positioned in relation to the following regions or reference lines:

• Margin: Depending on the anchoring type, the object is positioned considering the space between the top margin and the character ("To character" anchoring) or bottom edge of the paragraph ("To paragraph" anchoring) where the anchor is placed.

• Paragraph text area: the object is positioned considering the height of the paragraph where the anchor is placed.

• Entire page: the object is positioned considering the full page height, from top to bottom page borders.

• Page text area: the object is positioned considering the full height available for text, from top to bottom margins.

• Character: available only for "To character" or "As character" anchoring, the object is positioned relative to the region between the top border and bottom border of the character immediately before where the anchor is placed. A character formatted with a common border with other characters or objects uses the region for the highest character or object in the common border.

• Line of text: available only for "To character" anchoring, the object is positioned considering the height of the line of text where the anchor is placed.

• Baseline: available only for "As character" anchoring, this option will position the object considering the text baseline over which all characters are placed.

• Row: available only for "As character" anchoring, this option will position the object considering the height of the row where the anchor is placed.

• Entire frame: available only for "To frame" anchoring, the outer edges of the frame.

• Frame text area: available only for "To frame" anchoring, the text area of the frame.

Удерживать в границах текста

Keeps the selected object within the layout boundaries of the text that the object is anchored to. To place the selected object anywhere in your document, do not select this option.

By default, the Keep inside text boundaries option is selected when you open a document that was created in a version of Writer older than OpenOffice.org 2.0. However, this option is not selected when you create a document or when you open a document in Microsoft Word format (*.doc).

Зелёный прямоугольник обозначает выбранный объект, красный прямоугольник обозначает исходную точку выравнивания. При привязке объекта как символа исходный прямоугольник превращается в красную линию.

Формат - Привязка

Format - Align Text